1984-2007 Honda CR80R (CR80-R), CR85R (CR80-R), CR125R (CR125-R), CR250R (CR250-R) Lubrication Diagrams, Cable Routing and Service Manual Download Link.


Lubrication Diagrams & Cable Routing Diagram

1
SERVICE MANUAL DOWNLOADS
Always refer to your service manual before attempting to do any work on your motorcycle, important data including procedures, diagrams, specifications cleaning & maintenance information will help you care for and lower the chances of premature parts failurer. Below is a great source for service manuals available for instant download straight to your computers in just seconds.
1
All manuals are simple to use pdf downloads and are delivered straight to your computer in just seconds. Not sure what a pdf is? Here is a sample of what a  Service Manual looks like (sample is restricted to one page only).
 
HONDA CR125/CR125R SERVICE MANUALS
1
 

MODEL/YEAR APPLICATION:

Honda CR125R, CR125-R, CR-125-R, CR125 1984, 1985, 1986, 1987, 1988, 1989, 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006 & 2007 models.

Honda CR250R, CR250, CR-250R, CR250-R 85, 86, 87, 88, 89, 90, 91, 92, 93, 94, 95, 96, 97, 98, 99, 00, 01, 02, 03, 04, 05, 06 & 07 year CR250R models.

Honda  CR80R, CR85R, CR80, CR85, CR-80-R, CR-85-R 1984, 85, 86, 87, 88, 89, 90, 91, 92, 93, 94, 95, 96, 97, 98, 99, 00, 01, 02, 03, 04, 05, 06 & 07 year CR-80/85-R models.

It is only recommended to follow the factory service guide in the service manuals listed above when working on your motorcycle as these they contain the same information mechanics and technicians use to service your bike.

Important information not contained in this page like special notes, tips, proper procedures, complete specifications, torque specs, additional torque specs and recommendations must be followed in the instant download manual to ensure that the vehicle is in peak operating condition.

Related Searches:

LUBRICATION DIAGRAMS

LUBRICATION DIAGRAMS

1. Oil filter element

2. Oil pump

3. Drive axle

4. Main axle

5. Intake camshaft

6. Exhaust camshaft

7. Oil tank

8. Oil delivery pipe

A. To oil tank

 

1. Crankshaft

2. Oil filter element

3. Oil tank

4. Oil hose

A. From oil pump

 

CABLE ROUTING DIAGRAM

 

CABLE ROUTING DIAGRAM

1. Fuel tank breather hose

2. Radiator hose 1

3. Cylinder head breather hose

4. Radiator hose 3

5. Clutch cable

6. Throttle position sensor lead

7. Hot starter cable

8. Fuel hose

9. Carburetor breather hose

10. Carburetor overflow hose

11. Throttle position sensor lead

protector

12. Throttle position sensor cover

A. Insert the end of the fuel tank

breather hose into the hole in

the steering stem.

B. Aligh the paint mark on the cylinder

head breather hose with the

front end of the hose guide.

C. Pass the cylinder head breather

hose on the outside of front engine

bracket.

D. Pass the cylinder head breather

hose between the radiator and

radiator hose 3.

E. Pass the fuel hose on the outside

of throttle position sensor

lead.

F. Pass the carburetor breather

hoses and overflow hose so that

all there hoses do not contact

the rear shock absorber.

G. Insert the throttle position sensor

lead protector into the throttle

position sensor cover.

1. Sub-wire harness

2. Hot starter cable

3. Oil hose

4. Neutral switch lead

5. Radiator hose 2

6. Clamp

7. Ignition coil lead

8. CDI magneto lead

9. Neutral switch lead coupler

10. CDI unit lead coupler

11. Radiator breather hose

12. Hot starter cable protector

13. Rubber cap

14. Throttle position sensor lead

15. Cylinder head breather hose

16. Throttle position sensor lead coupler

17. Tension pipe

18. Radiator mounting boss

19. Cylinder head breather hose

20. Throttle position sensor tube clamp

A. Pass the hot starter cable over

the radiator mounting boss.

B. Pass the throttle position sensor

lead under the hot starter cable.

C. Fasten the throttle position sensor

lead and the hot starter cable.

D. Locate the clamp between the

hot starter cable protector and

rubber cap.

E. Fasten the neutral switch lead

below the oil hose. and pass the

neutral switch lead on the inside

of the oil hose.

F. Pass the neutral switch lead on

the inside of the oil hose.

G. Fasten the neutral switch lead,

CDI magneto lead, and radiator

breather hose onto the frame.

They should all be clamped

above the engine bracket to the

left of the downtube of the

frame. The clamp ends should

face backward and the rest outside

of the frame.

H. Pass the clutch cable through

the cable guide.

I. Pass the neutral switch lead and

CDI magneto lead behind the

frame.

J. Pass the hot starter cable on the

inside of the cylinder head

breather hose.

K. Fit the coupler projection into the

hole in the cover.

L. Fasten the sub-wire harness on

the CDI unit bracket.

M. Fasten the sub-wire harness at

the position-taped portion.

N. Pass each lead under the

clamp. Locate the CDI magneto

lead on the outside of the ignition

coil lead. Locate the throttle

position sensor lead, neutral

switch lead, CDI magneto lead

and ignition coil lead so that they

do not lie one on another.

O. Fasten the sub-wire harness to

the CDI unit bracket with the

clamp ends located under the

bracket.

P. Fasten the neutral switch lead,

throttle position sensor lead,

CDI magneto lead and ignition

coil lead. Fasten them around

the periphery of the recess between

the tension pipe and radiator

mounting boss on the

frame.

Q. Locate the clamp ends within

the arrowed range. Assure that

the clamp end does not contact

the cylinder head breather hose.

R. Pass the radiator breather hose

on the outside of the CDI magneto

lead and neutral switch

lead.

S. Fasten the throttle position sensor

lead and hot starter cable.

Fasten them between the cylinder

head breather hose and

throttle position sensor tube

clamp. Fasten the clamp with its

ends toward the right-side of the

frame and cut off the other end

with 3 to 5 clamp holes left in it.

T. Locate the radiator breather

hose end above the down tube

and between the oil hose and

engine guard.

U. Fasten the neutral switch lead

above the oil hose, and pass the

neutral switch lead on the inside

of the oil hose.

1. Radiator hose 2

2. Radiator breather hose

3. Ignition coil

4. Throttle cable (pull)

5. Throttle cable (return)

6. Engine stop switch lead

A. Put a cover over the ignition coil.

B. Pass the throttle cables through

the cable guide.

C. Pass the throttle cable over the

radiator mounting boss. Cross

the throttle cable behind the radiator.

D. Pass the throttle cables on the

outside of the ignition coil.

E. Insert the engine stop switch

lead into the CDI unit band.

Align the coupler lower end with

the band lower end.

F. Fit the hole in the CDI unit band

over the CDI unit bracket

 Honda CR, C-R, CR85, CR-85, CR85R, CR80, CR85R, CR-125, CR125R, CR125-R, CR250R, CR250-R